IDEM – Office of Air Quality – Permits Branch 100 N. Senate Avenue, MC 61-53 Room 1003 Indianapolis, IN 46204-2251 Telephone: (317) 233-0178 or Toll Free: 1-800-451-6027 x30178 (within Indiana) Facsimile Number: (317) 232-6749 www.IN.gov/idem OAQ CONTROL EQUIPMENT APPLICATION CE-08: Organics – Condenser State Form 52625 (R / 1-10) INDIANA DEPARTMENT OF ENVIRONMENTAL MANAGEMENT NOTES: • The purpose of CE-08 is to identify all the parameters that describe the condenser. This is a required form. • Complete this form once for each condenser (or once for each set of identical condensers). • Detailed instructions for this form are available online on the Air Permit Application Forms website. • All information submitted to IDEM will be made available to the public unless it is submitted under a claim of confidentiality. Claims of confidentiality must be made at the time the information is submitted to IDEM, and must follow the requirements set out in 326 IAC 17.1-4-1. Failure to follow these requirements exactly will result in your information becoming a public record, available for any one to inspect and photocopy. PART A: Identification and Description of Control Equipment Part A identifies the control device and describes its physical properties. 1. Control Equipment ID: 2. Installation Date: 3. Type of Condenser: Conventional 4. Condenser Category: Direct Contact 5. Dew Point Temperature: Refrigeration Cryogenic Indirect Contact Other (specify): Other (specify): ° F 6. Heat Transfer Efficiency (%): 7. Hood Static Pressure (specify units): 8. Is there a permanently installed Analyzer? Negative Pressure? No Yes No Yes: Unit ID of the analyzer: 9. Is the Condenser used for Steam Stripping of Organics? Yes No Not Applicable 10. Ice Buildup: Explain how you plan to address the potential for ice build-up. PART B: Operational Parameters Part B provides the operational parameters of the control device and the pollutant laden gas stream. A. Units 11. Organic Vapor Concentration (by volume) 13. Gas Stream Temperature inches of water C. Outlet D. Differential ACFM ° F 14. Gas Stream Pressure Inlet ppmv 12. Gas Stream Flow Rate B. 15. Coolant Flow Rate 16. Coolant Temperature 17. Vapor Pressure to GPM ° F psi to 18. Other (specify): Continued on Next Page Page 1 of 2 American LegalNet, Inc. www.FormsWorkFlow.com Indiana Department of Environmental Management Office of Air Quality State Form 52625 (R / 1-10) Organics Control Device – Condenser FORM CE-08 Page 2 of 2 PART C: Pollutant Concentrations Part C provides the pollutant concentrations of the pollutant laden gas stream. 19. Units 20. Inlet 21. Outlet 22. Efficiency (%): Capture Control a. Hazardous Air Pollutant (HAP) (specify): b. Volatile Organic Compounds (VOC) c. Other Pollutant (specify): PART D: Monitoring, Record Keeping, & Testing Procedures Part D identifies any existing or proposed monitoring, record keeping, & testing procedures that may need to be included in the permit. 23. Item(s) Monitored: 24. Monitoring Frequency: 25. Item(s) Recorded: 26. Record Keeping Frequency: 27. Pollutant(s) Tested: 28. Test Method(s): 29. Testing Frequency: PART E: Preventive Maintenance Plan Part E verifies that a complete Preventive Maintenance Plan (PMP) has been prepared for the control device, if applicable. Use this table as a checklist to ensure that the PMP is complete. 30. Do you have a Preventive Maintenance Plan (PMP)? No PMP is needed. Yes – the following items are identified on the PMP: A. Identification of the individual(s) responsible for inspecting, maintaining and repairing emission control devices. B. Description of the items or conditions that will be inspected. C. Schedule for inspection of items or conditions described above. D. Identification and quantification of the replacement parts that will be maintained in inventory for quick replacement. This space is intentionally left blank. American LegalNet, Inc. www.FormsWorkFlow.com